Roboteq Dual Channel Digital Motor Controller AX500 Uživatelský manuál Strana 122
- Strana / 154
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Serial (RS-232) Controls and Operation
122 AX500 Motor Controller User’s Manual Version 1.9b. June 1, 2007
The Controller Status Register can be polled at any time to see if there is a pending fault
condition. Any one bit set will cause the controller to turn off the Power Output stage. Con-
ditions marked as Temporary mean that the controller will resume operation as soon as the
fault condition disappears. Permanent conditions will cause the controller to remain off
until it is reset either by cycling power, pressing the reset button, or sending the %rrrrrr
command.
Controller Identification Register
Address: ^8A
Access: Read Only
Effective: Instantly
This register may be used to query the Controller’s model and some of its optional hard-
ware configurations.
Current Amps Limit Registers
Address: ^8B - Channel 1
^8C - Channel 2
Access: Read Only
Effective: Instantly
TABLE 21. Controller Status Register Definition
Bit Fault Condition Effect
0 Overvoltage Temporary
1 Overtemperature Temporary
2 Undervoltage Temporary
3 Manually Forced MOSFETs Off Temporary
4Unused
5 Confirmed Short Circuit Permanent
6 Confirmed Encoder Error Permanent
7 Emergency Stop Pressed Permanent
TABLE 22. Controller Identification Register Definition
Bit Model or Function
0AX500
1AX1500
2AX2500
3AX3500
4Unused
5 Encoder Present
6 Short Circuit Detection Present
7Unused
- Dual Channel 1
- Digital Motor 1
- Controller 1
- Revision History 3
- SECTION 2 AX500 5
- SECTION 9 Normal and 7
- SECTION 10 R/C Operation 81 7
- Important Safety 11
- Warnings 11
- Important Safety Warnings 12
- Quick Start 13
- Motor 2 Motor 1 14
- M2+ M1- M1+ VMotM2- 3 x Gnd 14
- RS232 Mode No Watchdog 18
- RS232 Mode with Watchdog 18
- Analog Mode 18
- Exploring further 20
- AX500 Motor 21
- Overview 21
- Technical features 22
- Connecting 25
- Power and 25
- Motors to the 25
- Controller Power 26
- Controller Powering Schemes 27
- General 35
- Position Sensor 38
- Gear box 38
- Position Feedback 38
- Command Control Curves 42
- Inverted Operation 45
- Sensors and 47
- Actuators to 47
- Input/Outputs 47
- AX500’s Inputs and Outputs 48
- I/O List and Pin Assignment 50
- Important warning: 52
- Analog Inputs 54
- Reported Analog Value 60
- Temperature in Degrees C 60
- Closed Loop 63
- Position Mode 63
- Important Warning: 67
- Important Safety Warning 68
- PID tuning in Position Mode 71
- • Command Value 72
- • Actual Position 72
- • Applied Power 72
- Speed Mode 73
- Tachometer wiring 74
- PID tuning in Speed Mode 77
- Closed Loop Speed Mode 78
- Fault Condition 79
- LED Messages 79
- Normal and 79
- Output Off / Fault Condition 80
- R/C Operation 81
- Selecting the R/C Input Mode 82
- R/C Input Circuit Description 83
- Supplied Cable Description 83
- 1. 0 5 m s 87
- R/C pulse timing: 87
- Joystick Deadband Programming 88
- Analog Control 93
- Analog Control and Operation 100
- Serial (RS-232) 101
- Controls and 101
- Operation 101
- Cable configuration 103
- Extending the RS232 Cable 103
- Communication Settings 104
- RS232 Mode if default 106
- Character Echo 106
- Command Acknowledgement 106
- Command Error 106
- RS-232 Watchdog 107
- Set Motor Command Value 108
- Set Accessory Output 108
- Important Notice 109
- Query Battery Voltages 111
- Query Digital Inputs 111
- Reset Controller 111
- Apply Parameter Changes 112
- Amps Limit 115
- Acceleration 116
- Input Switches Function 116
- Left/Right Adjust 118
- Default PID Gains 118
- Important Notice: 120
- Read/Change PID Values 121
- PWM Frequency Register 121
- Controller Status Register 121
- Current Amps Limit Registers 122
- Data Logging Cables 126
- Using the Roborun 131
- Configuration 131
- Getting On-Screen Help 134
- Control Settings 135
- Power Settings 136
- Running the Motors 138
- Logging Data to Disk 141
- Using the Console 142
- Important Warning 146
- Mechanical 149
- Specifications 149
- Mounting Considerations 150
- Thermal Considerations 150
- Precautions to observe 152
- Wire Dimensions 153
- Mechanical Specifications 154
Související produkty a manuály pro Hardware Roboteq Dual Channel Digital Motor Controller AX500
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.224 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce